Hallo! Tracked shipping to Austria with Delivery Duty Paid for just €3.99  

Ship to
Austria
0
  • argentina
  • chile
  • colombia
  • españa
  • méxico
  • perú
  • estados unidos
  • internacional

Select your country

Americas

Europe

Rest of the world

portada HVAC Math Handbook: A Complete Guide to Load Calculations, Formulas, Unit Conversions, Airflow, and Practice Problems for Heating, Cooling, & Refrigeration Technicians
Type
Physical Book
Language
English
Pages
477
Format
Paperback
ISBN13
9798171485887

HVAC Math Handbook: A Complete Guide to Load Calculations, Formulas, Unit Conversions, Airflow, and Practice Problems for Heating, Cooling, & Refrigeration Technicians

Engineering Press, Ridgeline (Author) · Independently published · Paperback

HVAC Math Handbook: A Complete Guide to Load Calculations, Formulas, Unit Conversions, Airflow, and Practice Problems for Heating, Cooling, & Refrigeration Technicians - Engineering Press, Ridgeline

New Book Imported to Austria
Delivery: 07 Dec - 09 Dec Shipping: 5 to 6 business days.
76,14 €
Import costs and 10% VAT included in the price ✅
76,14 €

Synopsis "HVAC Math Handbook: A Complete Guide to Load Calculations, Formulas, Unit Conversions, Airflow, and Practice Problems for Heating, Cooling, & Refrigeration Technicians"

Four hundred cubic feet per minute per ton. A constant of 1.08 on the air side and 500 on the water side. Every heating, cooling, and refrigeration technician runs on numbers like these — and almost nobody can say where they come from, or when they stop being true. That is because the trade's arithmetic is scattered: a sizing table here, a manufacturer's bulletin there, a slide chart on the back of a pressure-temperature card, a rule of thumb passed down a shop until nobody remembers what it was derived from. It works until the job leaves standard conditions — a duct run at altitude, an air handler in a hundred-and-forty-degree attic, a nameplate that mixes two measurement systems. The technician who has only memorized the number is stuck the moment the table runs out. And a wrong number in this trade is never an abstraction: it is an oversized furnace, a starved coil, a callback, a compressor that dies young. This handbook was built to close that gap. It gathers the calculations a technician actually performs — on a service call, at a start-up, during a replacement estimate — and works each one through from the physical relationship that produces it to the number written on the invoice. Where a shortcut exists, the derivation that justifies it comes first, along with the conditions under which it fails. What you will take from it: One conversion method that handles any unit conversion, including ones you have never seen before The sensible, latent, and total heat equations — and how to correct their constants when conditions are not standard A complete heat loss and heat gain calculation, from design conditions to room-by-room equipment selection Airflow verified by duct traverse and by temperature rise, the fan laws, and duct sizing by friction loss against available static pressure The refrigeration cycle read from two gauges and two thermometers — superheat, subcooling, compression ratio, and charge limits for the newer mildly flammable refrigerants Combustion arithmetic: clocking a meter, input, output, efficiency, temperature rise, and gas pipe sizing Pump curves, glycol corrections, and expansion tanks on the water side; amperage, voltage drop, and power factor on the electrical side — through operating cost and simple payback. The apparatus is built for learning and for the truck: 141 fully worked examples showing the equation, the substitution, and the units at every step; more than 400 end-of-chapter practice problems, each answered with a complete worked solution; a master conversion appendix with exact factors; every equation in the book collected in one place; reference data tables; a field quick reference; and a glossary of roughly 190 terms. Chapters are self-contained enough to open anywhere and cross-referenced enough to read straight through. Units follow United States practice, with an appendix for working any calculation in the units used across the English-speaking world. It is written for the apprentice meeting this material for the first time, the trade-school or community-college student with an exam ahead, the working technician tired of trusting numbers he cannot check, and the estimator or service manager who checks them. Stop working from numbers you cannot verify. Get your copy and start carrying the arithmetic that holds up when the table runs out.

Customers reviews

Frequently Asked Questions about the Book

All books in our catalog are Original.
The book is written in English.
The binding of this edition is Paperback.

Questions and Answers about the Book

Do you have a question about the book? Login to be able to add your own question.

Opinions about Bookdelivery

More customer reviews